Skip to content
Radium Fuel Hanger 11-UP Ford Mustang NO Pump Inc. for Walbro F90000274/285 E85

Radium Fuel Hanger 11-UP Ford Mustang NO Pump Inc. for Walbro F90000274/285 E85

by Radium
$598.44 - $598.44
$598.44
$598.44 - $598.44
$598.44

VEHICLE COMPATIBILITY

2011+ Ford Mustang, All (S197/S550)
2011+ Shelby GT/GTS/GT350 (S197/S550)
2020+ Shelby GT500 (S550)
13-14 Shelby GT500 (S197)

OVERVIEW
The Radium Engineering pump hanger is an excellent solution for increasing the fuel flow on modified 2011+ Ford Mustang vehicles. It can be used with 1 or 2 aftermarket pumps, with several pump options available. This drop-in unit replaces the OE in-tank fuel pump module and is safe for use with alternative fuels such as E85.
Unlike other drop-in pump hangers on the market, the Radium Engineering fuel pump hanger features a carefully designed collector box that keeps fuel trapped around the fuel pump(s).

Inside, the fuel pumps are carefully packaged, along with the associated wiring and plumbing. 

Fuel is fed out of the top plate through a single threaded port and low-profile adapter fitting. Fuel pressure is regulated inside the Radium hanger and is adjustable. The OEM fuel level sender is transferred on to the Radium hanger, so full functionality is retained.
The OEM fuel tank access cover and rear seat bench fit without modifications.

FEATURES
-Drop-In Installation
-Permits 1 or 2 Pumps 
-Integrated 1:1 Adjustable FPR
-Fuel Starvation Protection
-High Current Electrical Hardware
-Compatibility with Popular Fuel Pumps
-Anodized Aluminum Construction
-Gasoline, Methanol, Ethanol Compliant
-Fuel Resistant Tubing and Wiring
-Stainless Steel Hardware

IMPORTANT NOTE: This fuel pump hanger is only sold without pumps pre-installed. Pumps must be installed by the end user/installer. Refer to the installation instructions linked above. Pumps may be purchased with the hanger, but they will not be pre-installed in the hanger.

PREVENTING FUEL STARVATION
Several mechanisms work together to move fuel into the collector box and keep it full at all times, ensuring that the pump (or pumps) have adequate fuel available, even during aggressive driving. The internal pump(s) are supplied with fuel from 3 different sources: the venturi jet pump fuel scavenged from the passive side of the tank, the returned fuel from the integrated fuel pressure regulator, and the two one-way fill valves on the bottom of the collector box (shown below). These valves allow fuel in, but not out. 

VENTURI JET PUMP
The OEM venturi jet pump in the return line creates a restriction when using high flowing fuel pumps. Radium Engineering has redesigned the siphon system to eliminate this restriction but still effectively scavenge fuel. This means higher flowing pumps can safely be used without fuel pressure issues. Depending on fuel pressure, the venturi jet pump will consume 15-45 LPH from the feed line. Take this fuel loss into consideration when sizing the fuel pumps. Connection to the crossover venturi system is made easy with the provided SAE quick connections (shown below).
Also, if it is important for fuel pressure to hold steady after the engine is shut down, install one of the check valves somewhere into the fuel system.
NOTE: Fuel starvation may still occur in extreme circumstances (high speed track driving) with very low fuel level. Always top-off your tank if planning to participate in an extreme driving event.

INTEGRATED FPR
To mimic factory functionality, the Radium fuel hanger features an integrated adjustable fuel pressure regulator. This means it features a single feed line out (no return) that dead-ends at the fuel rail, just like the OE system. This makes the system a simple plug-n-play install into a Mustang with the OE feed line. The built-in regulator is designed to handle the high flow rates of aftermarket pumps.

For vehicles with forced induction needing 1:1 rising rate fuel pressure, the built-in regulator features a vacuum reference. If an intake manifold vacuum hose is connected, the built-in FPR will operate at a 1:1 ratio permitting fuel pressure to proportionally increase with manifold (boost) pressure. Conversely, the vacuum port can remain open to atmosphere and pressure will remain constant (like OEM).

For vehicles needing a return style system, see the optional 20-0806 kit below.

NOTE: 2 fuel regulator return orifices are included for fine-tuning the desired fuel pressure to the fuel pumps' flow rate and potential hose plumbing restrictions. Refer to the installation instructions link above for more details.
If using the built-in regulator, it should be the ONLY regulator in the fuel system.

PLUMBING
OUTLET PORT: The outlet on the hanger is female threaded for 8AN ORB (3/4-16 O-ring).  Because the S197 and S550 use different fuel feed line connections, two unique low profile SAE quick connect fittings are provided. This can always be changed using an 8AN ORBfitting.

RETURN PORT: The return port is female threaded for 6AN ORB (9/16-18 O-ring). This port is only required to be used if the 20-0806 Fuel Hanger FPR Block-Off (see below) is installed and return line needs to be attached. A plug comes preinstalled in this port. Radium offers a variety of 6AN ORB adapter fittings that can be used in this port (sold separately) for return line connection.

FILTERING: Always install a sock filter to the fuel pump inlet(s). The fuel hanger eliminates the OEM post pump filter in the factory unit. A low micron aftermarket filter is required to be installed downstream to protect the injectors from debris.

ELECTRICAL
The custom designed stainless electrical studs easily handle the high current demand that compact multi-pin bulkhead connectors lack. These serviceable connections are hermetically sealed and impervious to all standard and exotic fuels. Non conductive anodized aluminum acorn nuts are provided to prevent any accidental short circuiting. Electrical hardware is included for the fuel pump(s) and OEM level sender. Furthermore, the in-tank wiring is insulated with high quality chemically resistant PTFE.

Depending on the specific model trim, the OEM fuel pump wiring is designed for 15-30 amps of current. Depending on the pump installed in the hanger, the fuel pump controller wiring can be reused for a single pump (only). Radium recommends upgrading the vehicle wiring to ensure the fuel pumps are operating at their full potential.
The OEM fuel level sensor secures to the collector box mount shown above.
California Prop 65 Warning: WARNING: The items in this ebay listing are found to have compounds and chemicals known to the State of California to cause cancer, birth defects, and reproductive harm: Manufacturer Part Number: 20-0802-00
Brand: Radium